a-1.jpg (10779 個位元組)
a-2.jpg (5185 個位元組) a-0.jpg (6441 個位元組)
a-4.jpg (13192 個位元組)
64057雲林縣斗六市科加二路3號
No. 3, Kejia 2nd Rd., Douliu, Yunlin County, Taiwan 64057
Tel: 886-5-5519-922       Fax: 886-5-5510-033

E-mail:sanes@ms32.hinet.net      http://www.sanes-press.com
 
Double Crank Power Presses Change Traditional C Type Frame Into Straight Side Fram
hb021.gif (326 個位元組)High rigidity frame structure eliminating the opening
   distortion, fully realizing the highly efficient blanking and
   deepdrawing operation.
hb021.gif (326 個位元組)Eight long right angled slide guide rails provide confidence on
   installing high accurate die.
   Ensuring high accuracy manufacturing to be possible.
hb021.gif (326 個位元組)Improved back side operability and die conformability of the
   press.
hb021.gif (326 個位元組)Large side opening for simple installation to complete single
   and fully automated operation on coiled material.
hb021.gif (326 個位元組)High quality machine accuracy improving machine
   endurance, providing lasting value. Totally matching the
   requirements of contemporary high accuracy 
   manufacturing industry, an attractive and highly efficient
   model.
hb021.gif (326 個位元組)High efficient clutch / brake with high endurance, reducing
   operational noise to the lowest level, improve operation
   environment.

Highly Reliable Over-Load Protector Device                        

  1.Piston      
2.Hydraulic Cylinder   
3.H.O.L.P Device
4. Oil Tank  
5.Air Regulation Unit
 
nside the slide, there is one precise hydraulic cylinder, As soon as larger load or eccentric load occurs, the pressure of oil cylinder will be released. the clutch of press will stop the slide and complete the protection of press and dies. When over-load situation ends. move the slide to top dead center by inch operation mode, the hydraulic pump will automatically make up the hydraulic pressure to the original set point. To eliminate stick situation, just release the hydraulic pressure inside the oil cylinder.
High Transmission Wet Cltuch / Brake (Dry type clutch /Brake-Made in Germany <Optional>)
High performance and effciency wet clutch / brake linings provide lasting service life time, without the worry of being worn out.
Low inertia / High torque multi-disk design, ensuring more improved sensitivity on start and brake.
Unique design allows faster intermitten operation, good for synchronized operation with robot arm.
Low noise, zero pollution, fully complied to the future requirements of environment protection.
p2-3.jpg (10877 個位元組) Unique 8-faced right angled slide guide with extended rail structure located in the center of the slide, resulting no twisting torque. Making confident usage of accurate die, and high precision manufacturing to be possilbe.
Features Of Die Cushion
hb021.gif (326 個位元組) Guide Block bushing use oilful material which can eliminate daily oil check.
hb021.gif (326 個位元組) Guide block is made of medium carbon steel with hard chrome management, which promises higher rigidity and longer service life.
hb021.gif (326 個位元組)
The standard air spring type die cushion has 2 Air Spring, and 2 Pads, it could be 1 Pad & 2 Air Springs upon the requests of customers.
      To meet the needs of automatic multi-op. Process, it can also be of multiple cylinder sets.
Specification Of Die Cushion
                                                                             Model
Item
STD-160 STD-200 STD-250 STD-315
2
P
2
C
Capacity Ton 6.3 X 2 8.0 X 2 10.0 X 2 14.1 X 2
Pad Dimension  (LR X FB) mm 720 X 460 720 X 460 800 X 500 800 X 500
1
P
2
C
Capacity Ton 12.6 16.0 20.0 28.2
Pad Dimension  (LR X FB) mm 1490 X 460 1490 X 460 1650 X 500 1650 X 500
Stroke length mm 90 110 130 150
Die Clamps
                Model
Item
CB-2 CB-4 CB-6
CA-2 CA-4 CA-6
Clamping Force 2 ton 4 ton 6.3 ton

 


Draw-Out Rails
                   item
Spec.
Use Length Loading Total Length
RC-103 1000 mm 2 tons 1050 mm
RC-125 1200 mm 5 tons 1250 mm

 

Die Lifter
                    Item
Spec.
Lift Capacity Die Lifter Length No. of Cylinders No. of Rollers Model
DL50-750 1.1 X 3 750 3 8 STD-160
DL50-800 1.1 X 3 800 3 8 STD-200
DL50-900 1.1 X 4 900 4 9 STD-250
DL50-1000 1.1 X 4 1000 4 10 STD-315
Bolster Dimension
Model STD-160 STD-200 STD-250 STD-315
Bolster Dimension Area (mm)(LRXFB) 1800 X 760 2150 X 840 2400 X 920 2600 X 1000
T-Slot Dimension Applied Bolt 24 24 24 24
Diagram1 T-Slot No. 10 10 14 14
Diagram2 T-Slot No. 10 10 14 14
Hole No. 48 48 56 56
a  (mm) 340 360 420 420
cxd (mm) 85 X 85 85 X 85 100 X 100 100 X 100
b5  (mm) 150 150 150 150
b6  (mm) 150 150 150 150
T-Slot Dimension
Symbol / Number 28
Z1 28
Z2 46
Z3 20
Z4 28
R 2
Applied Bolt M 24
Slide Area

Model

STD-160 STD-200 STD-250 STD-315
Slide Plate Dimension Area (mm)(LRXFB) 1500 X 580 1850 X 650 2100 X 700 2300 X 800
T-Slot Dimension Applied Bolt 24 24 24 24
T-Slot No. 10 10 14 14
Relative dimension b1 (mm) 150 150 150 150
b2 (mm) 150 150 150 150
 

Specification of STD series

Model STD-160 STD-200 STD-250 STD-315
Short stroke Long stroke UNIT S L S L S L S L
Capacity ton 160 200 250 315
Tonnage rating point (above B.D.C.) mm 6 7 7 7
Stroke length mm 130 200 150 250 170 280 180 300
Stroke per minute (SPM) S.P.M 40-85 30-55 35-70 25-45 25-55 20-35 25-45 15-30
Die height, slide to bolster mm 400 450 450 500 450 550 450 600
Die height adjustment mm 90 100 120 120
Slide area (a1×b1)   mm 1500×580 1850×650 2100×700 2300×800
Bolster area (a2×b2) mm 1800×760 2150×840 2400×920 2600×1000
Approx dimensions Floor to bolster (h1) mm 900 1000 1100 1100
Overall height (h2) mm 3220 3295 3680 3735 3900 4105 4030 4280
Poistion of anchor bolt (a3×b3) mm 2300×1320 2500×1450 2600×1570 2700×1650
Floor space required (a4×b4) mm 2520×2400 2750×2600 3000×2800 3220×2900
Main motor HP×P 20×4 25×4 30×4 40×4
Air pressure required

Kg/c㎡

5 5 5 5
General Attachments
1. Hydraulic Overload Protector
2. Electronic Angle Controller
3. Miss Feed Device
4. Pneumatic Blower Device
5. Variable Speed Device (Inverter)
6. Pre-Set Counter
Optional Attachments
1. Pneumatic Die Cushion
2. Pneumatic Ejector Device
3. Photo Safety Device
4. Electric Grease Lubrication Pump
5. Anti-Vibration Mount
6.Quick Die Change System
7.Dry type clutch / Brake-Made in Germany